Hi Nordic
Is the command:
nrfjprog -s 820100511 --qspiini Qspinrf54l15.ini --qspichiperase --program nrf54l15_FILES.bin --log
We did use it for nRF52840, where able...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello, I am having issue to migrate a working project based on Azure IoT Hub Application code from 1.7.0 to 2.7.0, I have resolved all errors associated with changing the...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
I am working on a project using the nrf9160DK for initial firmware development. Trying out the SAADC i encountered that the measured values were always about 20% lower then...
