Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Background :
I'm working with an nRF51822-EK development board. We're working on a project implementing the S110 soft device. We need to create a minimalist Bootloader...
I try to follow
devzone.nordicsemi.com/.../
but on the paragraph Using the nRF51 Dongle
I always receive "No response from master emulator "
also after flash the board...
I've recently began testing the NRF51 SDK, however, due to some availability issues, I'm using the PCA10003 Board. I've followed the two Tutorials here, and I am able to get...
HI,
We have just upgraded our application to support the latest S110 v8.0.0 but also evaluated the possibility to use S120 instead of S110, so that our customer only need...
Hi,all!
I am programing an android ble app.And I have successfully connected to my device and get my own service(uuid:0x1600),and the characteristic in it(uuid:0x1601)...
Is there somewhere that we can see the defconfig file for the Raspbian images generated here (under downloads): www.nordicsemi.com/.../nRF51-IoT-SDK
We'd like to integrate...
Hi, When using RBC mesh and SD8.0.0 I often get assertion at line 189 in soc_radio_timeslot.c.
This file is part of sd8.0.0 and I dont have source code. Why is this assert...
Hi all,
I am trying to send data(rssi+MAC address) from GATT server to GATT client using sd_ble_gatts_hvx(). I added the service and the characteristic into the ATT table...
Hi,
Following the AN 29 "nRF51 Development with GCC and Eclipse v1.1", I cannot import any project on Eclipse for nRF51822:
In step 1.2 "Import existing Eclipse project...
I work for a small start-up. Our products monitor events and communicate via bluetooth with an Android tablet.
We are currently trying to make our custom circuit using...
I'm using
s110_7.1
sdk 7.2
DFU
updating application (application.hex + application.dat zipped) works fine, but when updating bootloader (bootloader.hex+bootloader...
Hi,Nordic support
Circuit design: Unused I/O pins
where can i found recommended I/O end terminal desing of unusing GPIO pins ?
I'd need such as pull-down resistor......
HI, I'm extremely new about Nordic component and device.
I buy a nRF51 DK for start understand hou BLE work, I attach to my pc, the green led power on and my pc know the...
With S110 v8.0.0's size increased to 96K, I'm concerned that my current memory layout is going to prevent me from upgrading to a future softdevice.
It seems that the only...
