Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Dear Nordic support team,
Could you give some rough estimates for availability of production-ready version of the S130 soft device?
Thank you and with best regards,...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hi,
Have some nRF51822-beacon's rev 1.1 that would fit perfect for some tests and proof of concept with an ANT application.
As I understand the 51422 and 51822 are the...
Hi all,
Could you recommend a way of connecting the nRF51422 with PC or laptop running Win7?
It seems that there is no BLE stack for Win7 and thus can't connect. I am...
I am making some NRF51822-based temperature sensor nodes, powered by CR2032 coin cells, and I would like to minimise power usage in order to maximise battery life. I am using...
Hi,
I am doing a BLE based project using NRF51822. I am asked to build a 2 layer board.
According to the reference schematic BALF-NRF01D3 has been used with WLCSP package...
Hi,
I'm close to finishing the implementation of a system with a recording device with nrf51822, working with 6 sensors with nrf24L01.
The recorder is in receiving mode...
I'm looking for an approach to RF coexistence between an nRF51822 bluetooth SOC and a WiFi module such as the WL1801. Does anyone have any experience or recommendations for...
Hi guys,
I tried to flash the pca10001\blinky_example onto a nRF51822 with nRFgo Studio.
Flashing the s110 worked fine. But when I try to flash the hex from the example...
Hello All,
I'm thinking a small plastic case for a portable device.
It is possible to place pcb board (with pcb antenna) above the battery (Li-Po) or can interfere with...
I want to log basic intermittent events and push them to a previously associated mobile device when one is nearby. The mobile device can then forward the events up to a server...
I'd like to know what is the minimum and maximum frequency I can generate on a GPIO with a 50% duty cycle (+/-10% at the worst case). Which resources should I use for that...
In my case active CE signal defines byte boundaries - for each byte individually.
From what I see, DMA seems to stop on rising edge of CS regardless what is declared in...
Hello everyone,
I'm using nRF51822 development kit to do BLE network experiment.
The boards I use are PCA10005 with omnidirectional antenna, and PCA10004 with PCB antenna...
