i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
I am trying to make a simple MAC-layer transceiver using Arduino environment. I have some code derived from this example: https://github.com/IoTS-P/nRF52-802154-Raw-Transmitter...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
I'd like to use the SBOM tool to generate a list of licenses used in my build.
I've been following the instructions here: Software Bill of Materials
In order to run...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I'm using a nRF52840 configured as Central and Peripheral, with nRF5_SDK 17.1.0 (I'm Not using Zephyr) for reading the Device Name from the Generic Service of a beacon. I...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
Hello, i have a question about antenna on PCB, the datasheet show me Grounding of C9 capacitor MUST be isolated from ALL ground layers except the bottom ground layer, I see...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if we can use one Ignion antenna, shared for the LTE and GPS.
On the original...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
