But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I know it is not recommended to use SD8.0.0 and SDK8 on revision 1 ( QFAAC0 ) based modules.. But as it is for testing purpose only and would save me a lot of time...
When not programed bootloader,my own 51822 module can work without Development Board,i supply the power through the button cell to my module.
But when programed bootloader...
Hi,
I want to use ble_app_multilink_central example for my own application. Here are my problems:
Setting MIN and MAX CONN_INTERVAL to more-less 20ms or lower (both...
Hi.
In my program I need a frequency at 2 MHz (a square wave with duty cycle at 50%), it should just run a frequency in a short time, under one second. Also the code must...
Hi,
I'm using a simple timer with interval set using "APP_TIMER_TICKS(1.4, APP_TIMER_PRESCALER)" alongside softdevice. Now i'm trying to get it to go faster but it would...
I got this error when programming the Development Dongle. The dongle is recognized in the
Master Control Panel as a COM4 - xxxx, and when is connected a green led and blue...
Hello,
We are French students in a school of engineers. We are developing a project based on the nrf51822.
Actually, we implemented RIOT OS on this SoC and we would...
I am currently using softdevice 8.0.0.
I am curious if the nRF51822 will be upgradable to be 4.2 compliant with a new softdevice release in the future? My understanding...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am trying to allow 2 peripherals to bond to a central, and would like to be able to use 2 push buttons to delete the bond information for either device. Is it possible to...
Hello, Nordics :)
I am trying to develop ANCS device with SDK 8.1, but I have some problem.
This are my environments.
Board: custom board.
chip: nrf51822AA...
Hi,
Function call to > err_code = ble_advdata_set(&advdata, NULL);
returns always err_code = 7 (NRF_ERROR_INVALID_PARAMETER) for a 128 bit UUID type (BLE_UUID_TYPE_VENDOR_BEGIN...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
