I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
I want to create automatic build using CI in bitbucket pipeline.
I would like to use image NordicPlayground / nrf-docker to compile the project. I saw the article Build...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
Hi everyone
I have installed the nRF Connect for VS Code Extension Pack later tried to install toolchain the latest is v3.0.2 it successfully installed but im not getting...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hi,
I receive the following build error: "../zephyr-project-v4.1.0/modules/crypto/mbedtls/include/mbedtls/check_config.h:96:2: error: #error "Unsupported partial support...
Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
