I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I am trying to run the ble_app_hrs on my nrf51822 based board in combination with the nRF51822 Development Dongle. I am following the instructions from nRF51822 Development...
How can I add PKT_TYPE_INIT (DFU Contorl Point - OpCode = 2) into my DFU?
S110 nrf51_sdk_v6_1_0_b2ec2e6
Chip nrf51822
Softdevice s110_nrf51822_7.0.0_softdevice.hex...
I have a nRF51822 chip sending me BLE UART data to my phone and it works fine with the app. No I want to send it to my PC and Read the data (and send commands) via PuTTY....
Hey guys, I'm looking for a printed antenna PCB file. I have already read the white paper and I think using a more complex antenna would save more space and increases the...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
MCP and iOS are generating a different event sequences for a long writes.
MCP: after the BLE_EVT_USER_MEM_REQUEST...
Hey, I noticed that most of the wearable ble devices (without keyboard and screen) on the market are using 'push to confirm connection' authentication, when you have to push...
Chip nrf51822
S110 nrf51_sdk_v6_1_0_b2ec2e6
Softdevice s110_nrf51822_7.0.0_softdevice.hex
I use "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\pub\device_firmware_updates...
Hi,
I am trying to set up a custom service and I have it all setup and it works properly. The only problem is that it is advertising as a 16bit service. I am moving from...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
What are the mechanics of using 'uuids_more_available'? Is this list transmitted as a part of advertising data, scan response data, or both? How does the host know that this...
I'm using mbed+nRF51822+BLE_API+softdevice 7.1.0 for BLE peripheral side. I add uart service with the setting BLE_GAP_CONN_SEC_MODE_SET_OPEN which is open link, and set the...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
