Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hello,
I have 2 issues, please help to let me know and clarify them...thankful for your support in advance....
I need to know the confirmation about the usage of fds...
I am using a custom board based on nRF52 (nRF52832-QFAB-R). I am using the ble_hid_mouse app and performing the initialization for SPI in the main routine. But with the SPI...
Hi
which is better for reduced current consumption
1. lesser value of of MIN_CONN_INTERVAL, MAX_CONN_INTERVAL with large SLAVE_LATENCY
2. or vice versa
Thanks...
I tried using the serial code in peripheral/examples to transmit At commands to the esp module but did no get any reply.Is there any reference example which I can use to connect...
Hello All,
We are working on automotive application can i use 3xspi in nrf51824. i.e is it possible to configaure 3 masters in nRF51824 ?
thanks in advance
pavan
I have the nRF52-DK arduino board with a nRF52832 chip on board, is there any examples where I can read the Analog inputs on the arduino board and send them over bluetooth...
I'm downloaded a copy of the "offline" documentation, but its just a html file, is there a copy in PDF or any other searchable format?
It would be nice to be able to search...
Hi. The same issue I have is described here, but I've been asked to post a new question:
https://devzone.nordicsemi.com/f/nordic-q-a/29084/why-sd_ble_gatts_exchange_mtu_reply...
I have several characteristics which are updated by a regular timer.
The characteristic property is notify. Due to memory issues I use as value location BLE_GATTS_VLOC_STACK...
Currenetly I access the gpio pins by using this code (P1.01 this pin)
#define PIN_1 ARDUINO_0_PIN
nrf_gpio_cfg_output(PIN_1);
and so on
Is there any other way to define...
I have decided to use nRF52 DK for my project for the first time.
I would like to know what brand of touch screen should be used.
I will use 3.5" and 7 or 10"
Thank...
im bought beacons from this china company (radio land )
the product link : www.radioland-china.com/.../6035982553.html
i could change name or uuid, major , minor with...
Hello.! I try nRF51822(softdevice using S130) SDK v12.3. I operate it as a master, but I leave it to distance to cut once and approach it afterwards, and, after a reconnection...
I need to stream 2 audio channels between two nRF52832 chips. I have two of the nRF52-DK boards and would like advice on which sample app might get me started in the right...
