I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hi,
I'm going to try not to get into stuff that is under apple's NDA, but my question is really on the nRF8001 side. Basically, the ANCS is a service that offers three...
I am definitely missing something here, but I can't figure out how to specify a subset of data to read from my peripheral.
Here's the setup: my nrf51822 device is a server...
Hi,
How to create new project for nordic controller using Keil
We are using pca10001 evaluation kit.
Actually in keil i open new project and select nrf51xxx board...
Dear Nordic Developer Zone,
I am trying to enable the readback protection in the main function just before the "wait for interrupt" sd_app_event_wait function using the...
Based on s110 v5.2 release note, nRF51822 will have future hardware revision.
What is the change for future hardware revision? Do we need to modify our circuit design for...
Hi all
My target board is nRF51822 , and I want to run the heart rate demo project,
but a error message when I compile it :
[b]Build target 'nrf51822_xxaa_s110 (256K...
Hi,
Now I want to make a project myself. My project include A/D and BLE for transmiting AD result. But I am confused about what BLE services should I add in my project. and...
Hello all,
I'm stuck in the use of the UART.
I have used the code from the UART example and the UART application for iPhone. I'm using eclipse because I don't want to...
Hi,
i have some troubles with my software which i doesn't understand maybe some one with more microcontroller Experience cann tell me how to solve this Problem.
I have...
Hi,
can someone post tutorial how to do Over Air Download? I mean new SDK 4.4
I get error from cmd: ImportError: No module named intelhex
Regards,
Konstantin
With the DFU sample from SDK v4.4.0.30888, I am unable to see the device in any host-side BLE monitoring utilities such as LightBlue (on Mac OS X) and our own custom BLE tools...
I need to transfer few kilobytes of data from slave device over BLE when requested from master device. I tough there is no file transfer profile in LE? What are the options...
Dear Nordic,
I know each sample has unique device address and stored in NRF_FICR->DEVICEADDR[0] and NRF_FICR->DEVICEADDR[1], and I think it has unique device UUID too....
In my ADC interrupt service routine (ADC_IRQHandler), I'd like to have a pointer available that I could use to carry some state from the main app thread to the IRQ handler...
