Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...
Hi:
In the datasheet, there have a description
Input range = (+- 0.6 V or +-VDD/4)/Gain
for a example, if Gain = 2, reference = 0.6V,
input range = 0.6 / 2 = 0...
In the SDK12.3.0 example ble_app_hrs_rscs_relay I want to add a uart to this example I added the uart_init part and the nus part, referring to ble_app_uart. However, when...
Hello,
What are the maximum number of node our nrf52832 and 52840 can support for
Zigbee?
BLE?
Thread - 1000?
Would this number be dependent on the memory size?...
Hi, I am using nrf24L01 for my application. I have to question:
- Is it possible to bypass SB protocol (I take into account possible error in exchanged packets without preamble...
Hello All,
I am following this tutorial.
https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I have modified "nRF5_SDK_15...
Hi.
I refer to this document. Stopped at Step.B1 now.
If you go to that path using CMD and then type "make", you will see the following problem.
'make' is not an internal...
Hello,
In my project (nRF52, SDK14.2) I have spi data flash connected to the MCU.
I'm trying to use SPI transaction manager library (nrf_spi_mngr) and face few questions...
I don't know how to use nrf52840 dongle as a sniffer. I look at the official routine. It looks like it really doesn't function as a sniffer. Is this what it is. If not, how...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
Hi!
We'd like to include a battery-powered remote control in our Bluetooth mesh network, i.e. we'll have a need for low power consumption.
In our mesh, devices may opt...
