Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am using nRF52832 pca10040 developement board. As I am begineer I dont know much about coding. I am using Eclipse IDE for developement. I want to transmit 1-10 numbers using...
BLE_GAP_ADV_SET_DATA_SIZE_MAX is use din ble_advertising.h
This macro is defined in ble_gap.h for each softdevice - however not in the header for S332. Also ble_gap_adv_data_t...
Is race condition possible when stopping advertising?
I need to disable BLE for some time to perform critical tasks. I need to stop advertising and be disconnected.
Let...
Hi Nordic team
As the title mention, I would like to program the DTM and radio test mode on thingy.
Did thingy support it?
Can I flash both program in thingy and switch...
Hi.
I scan devices with sd_ble_gap_scan_start command and on start it consumes around 6mA.
here are my parameters:
#define SCAN_INTERVAL 0x00A0 /**< Determines scan...
Hi,
For some reason when i do "project -> clean target" Keil deletes the softdevice Hex file in addition to the project compiled files.
Is that the normal behavior?...
I'm interested in operating the radio off of 32 MHz to avoid multiples of 128MHz. One options being considered is utilizing an external crystal of a slightly different frequency...
I'm developing a Multi-Role device using an STM32F3 and NRF52832 with Serialization. I'm currently trying to add Just Works encryption to the Peripheral of my device (that...
Hi
For some reason I get stuck in the softdevice. I manage to capture the sequence of the addresses
J-Link>s 0001B028: DB 68 LDR R3, [R3, #+0x0C] J-Link>s 0001B02A: 18...
Please tell me how to change the communication data length of BLE communication to 244 bytes and shorten communication cycle. Thank you.
I am using the version of [nRF5_SDK_15...
I know that there is a similar question here but the problem that the question is pointing on is not solved. Even in one of the answers is mentioned:
Now I found that...
When I run the example "ble_app_hrs_rscs_relay_pca10056_s140" on the development kit while debugging, then the SVC call for enabling the softdevice will stop at Address x8C4...
