Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Once GPIO is pressed (shorted to ground), I want to change the value of UUID or Major/Minor number
If not, the device will continue to advertise the previous values
Hello,
I am working on a custom project with nRF52832 using SDK14.2 and s132_nrf52_5.1.0.
Now I am trying to configure and use RTC2, and face the problem that ble_stack_init...
Hello everyone,
after hours of python module installation, I was able to run the PPK with PCA10056. I have cut the SB40 and used an external pwoer source with 2,5 V. I have...
Hi I have two problemes, I do not know where to start, so if someone has an example, I would like to see it. The first thing is if someone has an example about using pwm to...
When registering a base UUID with the SoftDevice via "sd_ble_uuid_vs_add", a uint8_t is returned which (per the ble_app_pwr_profiling example) is intended to be the "type...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
We are developing a React Native mobile application for iOS and Android, making use of the react-native-ble-plx library to interface with the BLE UART service from the examples...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
