I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi Nordic
I used spi0 to control the LCD screen. I succeeded and needed ble_ant, so I ported it to the ble_ant speed cadence sensor code I made.
But it does not see anything...
Hi,
I worked on the nrf51 for some years and recently moved over to the nrf52. PPI is a new interface I am exploring. I am having trouble restarting a RTC which was started...
Hello!
I have been lurking around the Thread SDK and I wonder if it is possible to get the IP-address of the device, and if so, how? I am stuck here so any help would be...
My nRF8001 device uses encryption with just works procedure.
Establishing a bond between nRF8001 and peer device as well as reconnection works on Android.
On iOS reconnection...
Hi,
I have download nrf5_SDK_for_Mesh_v1.0.0_src and want to start with nRF52840 DK and 52832. I could use EmbeddedStudio to flash it to 52840. Is there a app on the phone...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hi,
I have an application where both radio notifications and flash operations are used.
It seems that every sd_flash_write() generates two radio notifications. So during...
Hello Everyone,
I am using raytac's BLE module (nrf51822 chip antenna version, 32kb RAM 256 kb Flash ) (www.raytac.com/download/MDBT40/MDBT40-ANT-D.pdf) in our product...
Hi,
I have a problem with NRF_LOG_INFO() macro - it only shows messages form main.c file but not from another .c files in project. Why this could happen?
I work in Eclipse...
Hello,
is it possible to use a external clock e.g. a digital output of a TXCO. As source for the LF clock. So the same clock source as used for the host uC can be used...
Hi!,
I'm newbie with nRF52. I have a nRF51 Development Kit and a nRF52 Development Kit.
I have installed nRFconnect (for Ubuntu 64 bits) in Fedora 24 Workstation (64...
Hi! I have tried to use USB CDC ACM in my project but after running the USB CDC ACM example in the SDK, I found out that the example have the issue of not sending the data...
Hello,
So I'm constantly reading data using i2c into a variable. How do I transfer the data in this variable to the pc? It's just an array.
I understand that I have...
I am looking for a smallest size transceiver with an antenna done as part of the PCB layout (no external antenna needed). The simplest RF PCB layout is preferred, single frequency...
