I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
I am using the nrf52832 and according to the errata v1.1 the same contains a problem in the spi, according to clause 3.13 the engineering versions (QFAA-AA0, QFAA-AC0) and...
Hey..
I'm having difficulties using P1 pins for UARTE0 and/or UARTE1.
configuring the RX & TX pins like this works great:
#define RBP_UARTE0_RX_PIN_NUMBER NRF_GPIO_PIN_MAP...
Hi,
I'm using a NRF52832. I'm looking to measure the battery voltage. I'm using 2XAAA cells in serie (voltage range between 2V and 3V).
Below is the configuration to...
Sometimes, when I want to use the nrfjprog tool, I get the following error:
nrfjprog --log -f nrf52 --reset
ERROR: JLinkARM DLL reported an error. Try again. If error...
I cannot start Power Profiler Kit software. I followed the installing instructions, but ended up with the following:
>python.exe ppk.py
Traceback (most recent call last...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
Right now I'm facing two problems:
1. How do I properly handle interrupts while using...
There are tickets from 3 years ago that claim that nested CRITICAL_REGION_ENTER calls are not supported. Or they are supported if you write your own macros.
It appears to...
Hi there,
When using a PIN as RESET, what is the minimum activation time required to insure a reset?
I thought this should feature in Table 16.10.3 but I could not figure...
What is the logger message pool? There are two main definitions for it:
NRF_LOG_MSGPOOL_ELEMENT_COUNT
NRF_LOG_MSGPOOL_ELEMENT_SIZE
However it is not clear what it...
Hello ,
I want to use the NVIC to manage the interruption of the accelerometer and to run a specific program, are you ideas about the possibility of this?
Best Regard...
hi,
I am using nrf 52 DK and softdevice S132,PCA10040 board . I need to toggle a pin,set a pin,reset a pin .can anyone take this ticket to a sample code/ code snippet and...
