Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
HI ALL,
there is a sentence here 'Handles HVC events from the BLE stack.'
i am a newer here, please forgive of my silly question.
what is the HVC mean ?
thank...
Hi
I am using the nrfjprog.dll to program my UUT (nrf51822) during our production PCBA test. Apparently this is a bad idea to use this dll since you sometimes change the...
I found a possible bug in device manager in SDK 8.1.0 for S120. If you set for example DEVICE_MANAGER_MAX_BONDS 2 and try to bond another device, you get "No free connection...
hi
im using one of SDK Example and it stuck in this line of code
// Initialize SoftDevice.
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_75_PPM, NULL);
in this...
I have a UUID in which bytes 12 and 13 are not 0. For example, I have something like this
*addr = 87000d1f-1234-5678-9abc-123456789abc
When I use sd_ble_uuid_vs_add(&addr...
Please consider the images bellow, which can also be found here and here . The images represent the structure of a BLE packet, and the units used are bytes. The question...
Hi there,
I have tested out the BLE-NUS SDK firmware on the NRF51422 SDK Board, and it responded well. When I ported the exact same code over to my custom board, I received...
Hi,
I noticed that I can't bond successfully with my device using iOs 9.1 with Nrf Master control panel iOs app. When I insert the PINCODE, the device immediatly disconnects...
So I just received my nRF51 dk. When I plug it into the USB port, the device starts to blink but is not showing up as standard USB drive? Any suggestions?
Gabriel
Hello,
what general setup can you recommend to realize a Final Product Test only with BLE for mass production! (Without any additional copper contacts or NFC)
Some facts...
Hi I was reading up on all your chips.. NRF24, BLE and also on IPV6 capable..
Below are my requirements. Can you make a recommendation on what setup to use?
I have 4...
Hi
Im developing a filter - repeater signal on S130, and I want to advertise with a peridod of 20 ms for 10 seconds timeout.
I'm confused with FAST ADVERTISING AND SLOW...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
