Hi,
I'm working with a fleet of devices using the nRF52840 and NCS 2.6.0. Some of these are older devices with a bootloader that only supports RSA signatures, and I cannot...
We have been fighting with the Distance Measurement Toolkit for a while (see other ticket ). As we needed to move forward, we started the implementation of LE Secure Connection...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
How can I differentiate between a brown-out and an initial power-up on the nRF54L15? In my project, I need to detect a brown-out event in order to trigger specific actions...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi,
I am using the nRF51-DK board as a central running with ble_app_multilink_central_s130_pca10028 sample application. I am using SDK version 9.0 with Keil 5.14 version...
Hi all! I am using the nRF51 DK and I am trying to use the elements demo APPs that Nordic provide - the Beacon app. after the downloading of the app and watching it working...
Hi
In my application, I use some of the IO pins for a multi-purpose sensor interface, that I would like to be able to configure when the application is running. The interface...
Hi,
Can anyone help me where can find the example ble_hr ? I have changed the main file and it is saved and now I want the original example that was in C:\Keil_v5\ARM\Device...
I have IAR Embedded Workbench 7.40 installed with nRF5x_MDK_8_0_3_IAR.msi. However when i select nRF52832_xxAA i get the below message:
WTD: Unavailable option selection...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
