When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I have two nRF24L01+, one as PTX and one as PRX.
Both have following config: EN_RXADDR = ERX_P0, EN_AA = ENAA_P0, RF_CH = 100, RF_SETUP = 0x26, SETUP_RETR = 0xF0, SETUP_AW...
Hello, i have bought nRF51822 pcb module on Aliexpress (nRF51822 CEAA chip HWID 006A, 16Mhz crystal) and I'm trying to test it with SDK 6.1.0 and S110 v. 7.3.0 (as compatibility...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
Hello,
Using BLE Scanner app (available for Android), i'm able to change the device name. I can also write other values for each characteristic.
How can we protect a...
Hi,
I use nrf51822 with SDK8.1, S110 and gcc with Makefile. I want to use nrf_drv_twi in both my main “.c” file as well as a library “.c” file that is included in the build...
This is SDK 8.1.0, Softdevice 7.3.0 (not being used for this demo), running on a NRF51822-CEAA.
The minimal program below just sets the WDT for 10 seconds, then goes into...
Hi,
I have designed a custom board with nRF51822 but when I connect the custom board and j-link with an adapter the program nRFgo can't detect the chip.
When I conenct...
I'm using DK as the programmer connected (via Debug Out) to a naked nrf51 module (Rigado BMD-200). I can program it via DK, but RTT doesn't work (no output in J-Link RTT Viewer...
With the new nrf_drv_gpiote, how can I know if the handler has been trigged by event "low to high" or "high to low"?
Please, could you provide a configuration exemple?...
Hello,
I am a beginner. Just bougth a nRF51 DK but have not received it yet.
My second question of the day, very related to my first one, but thoutgh they were different...
Hello, beginner here. :)
I just bought an nRF51 DK, but have not received it yet.
I decided to test it because my older BLE module (HM-11) only allowed me to scan beacons...
Hello.
I installed all of relevant software tools and compiled blinky_example with nRF51822 Dev B/D.
Unluckily, build result is like below.
._build\blinky_arm.axf:...
I have built an application using SD120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or SD120, no pstorage functions...
Hello, My question is that in sleep mode my nrf51822 current consumption is 0.98mA, with only GPIOTE enable, however when I disable it, the current falls to 13uA, but the...
