why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
I use S110 V7.1.0,nrf51822 chip,
now I need write and read flash data in BLE mode.
When can I write the flash data at BLE mode?
When can I read the flash data at BLE...
I'm calling the requestData function and lib_aci_close_remote_pipe at the same time.
The lib_aci_close_remote_pipe returns 0x8E command error which means: "Command rejected...
Hello,
I need to store some app configuration on the FLASH and I'd like to use the features of pstorage module.
I don't understand the following thing ...
When the...
Hello,
I am currently using the SDK setup from this URL: embeddedsoftdev.blogspot.de/.../ehal-nrf51.html
In order to use that setup, one must change a line in the file...
Hello,
I downloaded MDK arm from Keil website (keil mvision 5), SDK and MDK pack from nordic download site. After installing SDK, I am not able to find example projects...
Hello,
I have quite a few of setting on my nodes and I want to save some of these permanently. Currently I am using the pstorage module and everything works as expected...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
