Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi , I tried to change the transmission power using the s110 API and tried checking if the value of the register storing the transmission power is changed or not. Following...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
I've got 4 services with 15 characteristics between them. Trying to add any more than that results in sd_ble_gatts_characteristic_add() returning NRF_ERROR_NO_MEM .
All...
Hi Expert,
I found a weird case that at my 51822 plaform with s110 enabled, if I define a global buffer like:
static uint8_t system_buffer[1024];
it obviously will...
Hi
The nRF24Le1 has 256 bytes in the infoPage for user data, starting 0x0100.
My question is how to write to that area?
Is it accessible from nRFgo Studio?
Is it accessible...
Hi every body,
Is there any way to increase the support packet per connection to more than 1 packet for S120 softdevice if i have just single slave and single master? ...
HI,
I have followed all the steps from devzone.nordicsemi.com/.../ and I can relay text between Termite & my iphone.
Can someone share a function / method which I can...
