I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I wanted a COAP Server running on nRF5340dk with DTLS and NS-Target without success. Whenever there is an attempt to connect to it from outside the app freezes, eg. shell...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hi
I want to use nRF54L15_DK run RSSI test
I know Desktop App on PC "RSSI Viewer" only Support nRF52 series,
Q1：How can I use Desktop App to run RSSI test?
Q2：Can...
I am currently working on a project involving the nRF52832 SoC using nRF5 SDK v15.0.0 . According to the nRF52832 Product Specification v1.4 , it is mentioned that P0.00 ...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hello everyone
I created a custom board with reference to thingy:91 for the antenna part. The board is 50x50 mm in size.
I tested the board and there are no problems...
Dear Experts,
I would like to better understand what exactly is accomplished by the mode-0 synchronization in Channel Sounding. My current understanding is that it seems...
Hello, I am following the instruction on dev academy - nrf connect sdk intermediate lesson 2 excercise 1, but I can't select data tab on memory explorer.
I can select only...
