I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...
Hi all,
I would like to trigger some actions on difference devices communicating with the ANT protocol based on the distance they are from each other. A simple example...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
First of all thanks for Nordic team for the excellent support. It is very useful for a beginner like me to get started on BLE development.
I am using the nRF51422...
The issue is that if a peripheral needs to enable interrupts (or anything else partly protected by the SoftDevice) and is configured before enabling the SoftDevice, the NVIC_...
Hi, I use nRF24LE1 configured for power down on register retention mode with RFRx active.
When the CPU is on power down i don't have any interrupt from RFIRQ.
Init configuration...
I downloaded the power consumption example code to a nRF51-DK to measure the current consumption during SYSTEM ON and SYSTEM OFF state.
For the SYSTEM ON state, I used...
On our custom board, we have a dedicated hardware reset IC which toggles the nRF51822's nRST line low in response to a magic button press. The nRST line has an external 100k...
Hi,
it's possible to decide if send a scan req to a peripheral device? I want to send a scan req only to the peripherals that have a specific adv packet...it's possible this...
So, I am working on a handful of nRF24L01 to test some ideas out with radio devices and read thru many example source codes, libraries and datasheets and now I am going a...
Hello everyone
I want to develop a prototype by using nrf51822 but the problem is i did not find information concerning the packages please i request you to provide the...
