Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
I use nRF51822 Model in my project that I need to run bluetooth advertising all time. And when I measured current, I found 1mA that is not enough to run for 1 year by just...
Hi,
My project include two MCU with n51822 and STM32. I expect upgrading STM32 application firmware by n51822 DFU function. Do you give your advice to implement it by modifying...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
I don’t fully understand the nRF51 event NRF_RADIO->END. NRF_RADIO->END identifies the completion of a packet transmission or reception. My question is what triggers NRF_RADIO...
We have a project that involves both battery-powered 'slave' devices and a mains-powered 'master' device (which needs to support multiple slaves and support WiFi). We are...
Hi,
imagine that I have a proprietary characteristic that allows only READ operation (from a smartphone for example) that expose an internal value in my application.
I...
Hi,
I'm using nrf51822 and SDK 6.1.
devzone.nordicsemi.com/.../
I learned how to store data with using pstorage library.
but I can't register block more than 1024...
