hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi all. I fell into despair in an attempt to find a solution. If I do not use sprintf then everything works fine.
Before calling some_f, mqtt_put works without any grudges...
Function softdevice_enable() doesn't return any adjusted warnings in case of changing central/peripheral connections, e.g. my ble_stack_init() function:
static void ble_stack_init...
Hello, nordic.
I studing nfc example for oob pairing.
So, I have to intergrate to uart example and hrs nfc example.
I had intergrated uart function in hrs_nfc example...
I am trying to decide whether to use free-rtos or bare-metal.
In the documentation for the nRF SDK v15.0.0 i see that free-rtos is not supported for the nRF52840.
However...
SDK14.2
A little background on this question.
I am creating a library where I need to add items to a queue and then process those items from the queue. I would like to...
PLEASE revise the page Getting-started-with-the-rRF52-Development-Kit to include
"confirm that the nRF52 DK has appeared as a removable drive named "JLINK"...
If drive...
Hi,
Iam using serialization application code from sdk14 nRF5_SDK_14.2.0_17b948a/examples/ble_central/ble_app_blinky_c and
connectivity code from sdk14 nRF5_SDK_14.2.0_17b948a...
Hello everyone,
Similar question like mine was asked, but I didn't quiet get the answer i was looking for. I will try to keep it simple, when I open altium files of thingy52...
Hello,
I am evaluating the module MBN52832 from Murata (Using the development kit). I have installed nRF Connect v2.3 and I have installed and launched Bluetooth Low Energy...
Hi,
In this topic , i was asking about how to increase range in mesh networks. I did some outdoors tests (clear field), changing power (-40, +4, +8 dBm) and mode (1MB and...
I am using nrf52832 to develop based on SDK14.2. I have defined a custom service . There are 7 characteristic in this service. The attribute of each characteristic is set...
When broadcasting mesh messages I use the access_reliable_t struct to set data.
I need clarification on what the contents indicate. The documentation is sparse and doesn...
I'm trying to model up current consumption of our system. I'm looking to put the nRF52840 into System OFF, no RAM, Normal voltage mode and waking up on both GPIO and USB Detect...
Hi,
Is there a list of the exact part numbers for all the components used in the nRF52832 reference designs? I could only find a pretty general Bill of Materials in the...
I am planning to make a custom board using nrf52832 ,for that i need to know what are all the steps need to be followed to perform OTA DFU to upload a custom firmware . List...
