Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
I'm currently using SDK v14.2.0 and I'm attempting to merge the buttonless DFU bluetooth example into the bluetooth template project within the Eclipse Oxygen environment...
Hey Guys,
I have 3 tasks running on FreeRTOS, SDK v14.0.0. In each task, I want to use SEGGER_RTT_printf() to debug.
I currently just call SEGGER_RTT_printf() without...
I have two nrf devices nrf51822 and nrf52DK, In nrf51822 i'm using S110 and i had created a custom service with 10 characteristics. If i connected to nrf connect i can able...
Hi,
Is it possible to make realization of this protocol ( wiki link ) with softdevice? After reading forum I think "more no than yes" because softdevice blocks CPU and this...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
Hi all,
I am working on Temperature and Humidity(DHT11) with nrf52832, After advertising the Bluetooth i am calling the DHT11 sensor function in loop, few seconds it is...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
