Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
(I've seen several other posts mentioning similar issues, but many of them haven't resolved or found a solution that seems to apply in my case.)
I have a custom board that...
Hi,
I have a simple and basic question. it may be chilly. the internal flash memory can store the data, but the question is it has stored as byte per address or word per...
I am using a nRF52840 chip in a custom board. I will be using all the SAADC channels, as well as 4 SPI connected ADCs.
The board itself will likely be powered for days at...
Hi !
I am using NRF52DK and I want send some daat with BLE. I have to send 800 bytes in BLE by packages of 25. So I tried this :
BUT when I look my uart terminal, I...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi Nordic,
I started from an empty project with peripherial control first, the code size is about 12KB. Then after adding peer manager and related code(fstorage, fds and...
Hello,
I build a custom board with Nrf52832 , to drive Relays , all works without load , no problem for drive the output.
When i put a load sometimes my device disconnect...
