Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi!
I'm working on HID mouse example on SDK 13.0.0, SoftDevice S1332 v4.0.5. I'm supposed to use this as a low power media button control, using a nRF52 DK. I've done a...
Hello,
We wish to use nRF52832 IC in our design. We will design an equipment which can connect to another device via BLE and can send some measurement data. Our equipment...
Hey everyone,
I'm working with nRF52810 . I want to write into UCIRs before program execution starts.
I tried to configure NVMC(Non Volatile Memory Controller) and then...
I am using the nrf905 in a project. The datasheet suggests crystals of 4mhz, 8mhz, 12mhz, 16mhz and 20mhz are all acceptable. Does the choice of crystal oscillator frequency...
Hi there, I have an 70mm wide and 50mm high PCB with an free space of about 32x26mm on the right top corner. At the moment this area is free of any traces and polygons. The...
In previous questions I inquired about setting the MTU size beyond 27 and thank to the answers I, indeed, manage to compile and run my program with larger MTU size definitions...
Hi, I have an issue with the watchdog and sd_app_evt_wait() when running the softdevice. It seems impossible to not let the watchdog go off while having an idle ble connection...
Hi there,
We're looking to improve the touch performance of our products by moving from PCB electrodes to a dedicated touch film. Can anyone provide any references to info...
Hello Nordic team,
What is the Maximum sampling frequency for i2s we can configure to nRf51 or nRF52 DK?
And if we enable UART module to print live of i2s on serial console...
Hi
I following the steps listed in the document Thingy Mesh Demo v0.1
https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
When i perform the step 5 "Open the...
Hello,
I am using sdk12.2.2 and nrf52 customized board. I want that user should be prompted to enter passkey before bonding. I refereed the code snippet from devzone and...
Hi!
Im using SDK14.2 and I m working with the custom characteristics tutorial(the one compatible with the SDK 14.2).I have an SDK5 device connected to a LORA radio with...
Hi,
I’m having some troubles writing into the fash memory. I work on KeilµVision.
I initialise flash doing :
uint32_t page_size = NRF_FICR->CODEPAGESIZE;
uint32_t...
I am adopting a project which was initiated by someone else. I am using GCC toolchain eclipse while previously used by other colleague who initiated the project used IAR....
Hi,
My product is automagically disconnected from the central after 9min of connection...
The same problem can be reproduced from the ble_app_template example as is, on...
