Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
In porting from SDK6 to SDK9, it looks as though
nrf_gpiote_task_config()
has been replaced with
nrf_gpiote_task_configure()
What, if anything, has replaced
nrf_gpiote_unconfig...
I'm using sd_ble_gap_address_set() to randomize mac address and it's working fine. But I'm confused about how to change it back to normal(initial value I see) once I wan't...
i cant find lbs example on \SDK8.0.0\examples\ble_peripheral\nrf51-ble-app-lbs-master\arm and compile.I planned to work with nrf51822 dk. The given example in github shows...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
Sorry but I've been stuck on this for a few days now and I have to give up and ask for help.
I'm attempting to set LED0 when BUTTON_0 is pressed and LED1 when BUTTON_1...
Hello all,
I am working on a device (nrf51 and s110) which is going to communicate with multiple centrals (smart phones).
The device uses a whitelist to connect to only...
Hi,
I run a custom board with an nrf51822.
If I program the device in the IAR IDE everything works fine but I cannot program the generated hexfile with nRFgo Studio or...
Is it 'NRF_RADIO->TASKS_DISABLE' or 'NRF_RADIO->TASKS_DISABLE = 1'?
Restarting advertisements seems not to be affected and I guess 'cancels out' NRF_RADIO->TASKS_DISABLE...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
