Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...
Hello everyone,
I’m fairly new to Android development and currently building a BLE app using Kotlin in Android Studio. So far, I’ve managed to implement scanning, connecting...
After a fresh installation of NCS 3.0.2 SDK and toolchain via the VScode extension, all west modules are reporting modifications:
PS C:\ncs\v3.0.2\zephyr> west status =...
HI DevZone,
I am trying to add the coded phy features in Peripheral_Uart and Central_Uart examples of NCS. I hope Coded phy features are successfully added into Peripheral_Uart...
Hello,
To finaly adjust the inside crystal capacitor at the end of production, I need measure the LFXO and HFXO frequencies signals to fine tuning. How should I do ?
Best...
Hi Nordic DevZone !
I'm facing an issue that I cannot manage to fix by myself.
So here is the brief: I'm trying to create a BLE beacon that will send some analysis results...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
