Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
I'm using NRF51822 with soft device version 6.0.
I'm trying to create an event which should be triggered every 24 Hours. In the current implementation in our code base...
I saw the demo of nRF52832 connected 20 peripheral devices and control the light in the peripheral.I would like to know the more deatil of the whole operation in chip/SD....
I've searched and the majority of answers seem to be years old.
I have an existing app_timer event handler that works perfectly, blinking LEDs.
I will soon have another...
Hi! I'm using two RedBear Nano v2 and I'm trying to read a long characteristic from one of the two devices. As I read in other posts in the forum, I need to invoke the read...
If I'm not mistaken, both S110 and S130 support OTA DFU right?
I understand that nordic semi most likely recommend S130 over S110, but please understand that
my current...
I have previously developed on the nRF24LU1+. This device would have a CHIPID in the InfoPage, This ID would have guaranteed it does not violate the requirements for ESB addresses...
Hi, im using NRF52832 whit SDK 12.3.0, when i compile this error appear, "undefined reference to `nrf_drv_spi_init", i included the "nrf_drv_spi.h" file.
also try to include...
Hi everyone,
I'm working with nrf52832 and i'm trying to send data over BLE for communicate with a mobile app. I saw that we could pass data with the function ble_nus_string_send...
Minor nitpick:
The PS_v1.0 datasheet says that "see the Reference Layout section on the Downloads tab for nRF52840 on..."
There is no Reference Layout section on the Downloads...
I am working on a BLE bootloader using SDK 14.2.0 on an NRF52832 device, using softdevice version 5.0.0. I am able to get the bootloader up and running, and I am able to see...
Pre Conditions:
1. As soon as the connection is established the App start a timer to disconnect the link using sd_ble_gap_disconnect
2. The app timer has the same timeout...
Hello,
I'm searching the possibilities of Thread mesh network. And I want to minimize the size of border router as small as possible. Have you considered to port the border...
Hi,
I'm having trouble writing to a characteristic when operating as a central. I'm sure it is just a lack of understanding on my part but neither the SDK documentation...