I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Hello. I am having trouble setting up two PWM channels on nrf51822. The device is running S110 and SDK9.0.
The PWM initialization sequence looks almost identical to the...
Hi,
With reference to This link , I'm trying to make a Nordic solution which can support all beacon applications (iBeacon, Eddystone & Altbeacon).
I'm able to integrate...
Hello I am trying to program this nrf51822 module. I am using J link Cortex M9 . I want burn multilink peripheral in it.
I have followed this link.
I have connected everything...
I would like my device to advertise for 10s and then begin advertising again only on an external interrupt.
What steps are required to restart advertising without restarting...
I am trying to reprogram a usb dongle device from AdaFruit (Bluefruit LE Sniffer), which uses the nrF51822 SoC, using nrFGo Studio. In the device manager I'm innRF5x Bootloader...
Hello everyone
i am trying to set the password for connection whenever its start advertsing but the static passkey option will set the pssword only for bonding not for...
Hi.
I am using nRF24, nRF51, and nRF52 chips.
Today I saw nRF31562A on some device(wireless mouse of Logitech)
However I can't find any information about this chip,
even...
Hello,
I would appreciate if you could help me solve what i am trying to do. I have nrf51DK board with nrf51422 on it, PCA10028, S130 and i want to use to scan for another...
Hello,
I am working on SDK 9.0 and softdevice 8.0 and the requirement for my application is the device has to advertise till it gets connected and even after disconnection...
Dear all,
I get a new nRF51-DK and I am trying to download an hex file into it.
I downloaded and installed nRFgo studio.
I connected my nRF51-DK to my...
Hi. I've gone through a lot of documentation and can't seem to find if this is documented by Nordic semi.. please answer if you know, or can point me to experiments/documentations...
I soldered 5 pieces of PCBA with nRF51822, but I got only one PCBA which can connect to J-LINK. I checked the bad four and found that SWDIO of nRF51822 on the four board is...
I'm having a weird hardfault and, I can't make sense of it.
Here's what I do know:
nrf sdk 9.0.0;
nrf51422 on a dk;
I have RTC1, SPI0, and TWI1 enabled (also a uart for...
