Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...
I am trying to setup the examples for the dev board PCA10040. I copy them from the Pack Installer and when I open the project I keep getting "Install missing Software Packs...
Hello
I made a custom service with characteristic. It send the number 1234 over ble. When i open the Master Control Panel and look at the custom characteristic. I read...
We have a home made BLE device based on nrfR1822. This one has two embedded sensors sampling data at a frequency of 25Hz.
In regular mode, the device sends every second...
I was going through Gazell link layer as well as Enhanced shortburst i found in both of them we can use payload max upto 32 bytes. Both supports 8 nodes with an host using...
I just received the nRF52 demo board PCA10036 V 1.0.0, and I also downloaded the latest SDK nRF52_SDK_0.9.2_dbc28c9
I programmed the softdevice hex and then programmed...
Hi BLE Developers,
I'm developing a BLE peripheral device using S110 softdevice which doesn't have any input or output capabilities and will communicate with smartphone...
Hi,
I am using the iOS nRF Toolbox and integrate it to my Swift project.
After that, I got this error message.
Undefined symbols for architecture x86_64:
"_crc32"...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I've been trying to wrap my head around the app_twi library by looking at the examples, and I'm slowly getting there.
However, for my application I need to send multiple...
There is a fair amount of documentation suggesting that a Raspberry Pi or consumer router running OpenWrt can be set up as an edge router for Bluetooth.
The builds involve...
