Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Here I´m again,
Maybe sound a little bit silly but I´m not able to find a way or a solution to make simply a Characteristic with more than one attribute. Something similar...
Folks,
Is there a document that describes the events generated by the S110 Soft Device and their interpretation? (Note: they're not listed in the S110 SoftDevice Spec v1...
Hi,
This is loosely related to the other question I asked a few weeks ago ( devzone.nordicsemi.com/.../two-interrupt-events-on-timer0) but this time I want to have two timers...
I am developing a Windows7 Visual C++ application to interface via Master Emulator to BLE device.
Where can I find the C/C++ header and lib files? (I am new to Nordic BLE...
Dear Nordic Devloper Zone,
I am facing a problem with RTC timer.
Here is a scenario :
I have an IOS application which is able to set the current time on the nRF51822...
As I understand it, like most modern PHYs the central and the peripheral are exchanging symbols to maintain link integrity and adjust Tx power to maximize battery life.
...
From what I am reading in the S110 spec, this service is supported but not adopted (i.e. example code. Is this correct? Has anyone implemented a navigation and location service...
Hi all
My hardware is nRF51822 PCA0000 and PCA0001,
I just want to compile/load any UART example to test my UART workable or not.
So I have tried example project button_radio_example...
Hello,
Having a problem with the 1 wire sensor DS1820, I've created my own 1 wire protocol functions. They compiled without any errors. but when I run my program, it only...
Hi,
I'm currently developing a board that utilizes a NRF51822 and I'd like to utilize the meander antenna from the PCA10000 dongle reference design. However, I'm using Eagle...
dear Nordic:
i created a new characteristic assigned UUID 0x18e1.in order to be writable,i set its properties with following in
static uint32_t pressure_high_byte_char_add...
I'm measuring current consumption on nRF51822, making code changes and then flashing/debugging via JLink GDBServer and gdb.
Right now it seems like I either have to physically...
Hi,
I´m using nRF51822 with my own application and I want to connect just to one specific master device (for example smartphone) after this one is bonded:
nRF51822...
Hi There,
I am developing a desktop applications (C#) using NRF2739 dongle and NRF8001 on the other side. Things were going very well using the masterEmulator.dll provided...
