Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Working with an nrf52805. Copied a simple example (peripheral_LBS) and found that RAM overflowed by ~2.2K I note that the nrf52dk_nrf52805 is not listed as a "compatible"...
Hi Team,
I am using nRF52840_DK to program my custom board but I am facing some voltage related issue from VDD pin.
Measuring on board it's giving 3.0V for VDD & GND but...
Hi
Two questions as below
1. About nPM1300 & nRF54L15 I2C connection, at nRF54L15 side, I put SCL/SDA at P1.x group, so INT also need at P1.x group? Or I can put at P0...
https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/
There are two "Section...
Hi,
I have designed a custom board using the nRF52840 and have successfully programmed it using SWD (SWDIO & SWDCLK) with a J-Link programmer . However, I now want to program...
Hii,
Downloaded Timer code from sample and trying to build using 2.9.0 SDK but not able to build. It is building using 2.6.2 sdk.
Pls check and update soon.
Thanks...
Hello.
I started using a custom board with the nRF5340. After flashing the program, it seems that protection was enabled, and operations such as erase, read, and write became...
Hi ，Nordic team
I applied QSPI driver QSPILCD and encountered the following problems: question 1, use nrf_drv_qspi_write write data: header and tail will be a few more bytes...
I'm trying to migrate my project from the child/parent build system to the new sysbuild system in Zephyr, and I'm finding it a bit unclear. I came across a helpful post that...
I used to use ncs2.8.0, but now I have updated it to 2.9.1. I upgraded the SDK and toolchain to version 2.9.1 in VSCode, but encountered this prompt when selecting version...
Dear Sir/Madam,
In the NRF date_time_ntp.c, the fraction of the NTP message is completely ignored in the line:
* date_time_ms = ( int64_t ) sntp_time . seconds * 1000...
Hi there, I have a nrf54l15 pdk and i want to get any uart log with my kit. I tried the quick start hello world code but it wasn't load application core and reset device....
I sometimes have bonding issues. Most of the time, bonding works fine. But occasionally, It looks like the Nordic SDK on the peripheral sends messages too early. The peripheral...
