Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi Nordicsemi,
I am working on peripheral BLE device, the device accessible from smartphone i am also writing the smartphone app, i want just my app to be able to connect...
Just received my Nordic nRF Smart Beacon Kit and was following the instructions in the User Guide to get setup. I inserted the battery into the beacon and there's an LED flashing...
My project is working but nRF connect does not seem to show it properly when advertising. It shows up for a moment then dissappears then shows up a while later on the RSSI...
I did try to SPI example in nRF5_SDK_11.0.0
But, I saw print in serial terminal only one-byte log which is NRF_LOG macro.
Basically, It SPI example included app_uart.c in...
Can't transmit a modulated carrier for FCC testing
part: nRF52832
We are writing our own firmware to support FCC testing. We have been successful at controlling the chip...
Our project use 51822 and another MCU stm32 to transmit heart rate data by uart. then 51822 SPP heart rate to smart phone APP. Now, We meet a issue that 51822 UART will crash...
Hi,
I just found what looks like a bug in ble_nus.c in SDK12 - not sure how to report it so I'm just doing it as a question/answer combo.
Basically:
Connect to...
Hi,
I'm developed a custom nRF52 board, and the main method to reset is via power cycling the power source (battery). Using GCC, should I still keep:
CFLAGS += -DCONFIG_GPIO_AS_PINRESET...
Now, I'm using the SDK12.1.0 and the device is NRF52832, I trying to use the secure DFU bootloader, when I open the Project Nordic provided(PCA10040 Debug) and build it, the...
Hello,
I have a PCA10028 that I want to use as a sniffer using the NRF Sniffer firmware. I tested it in macOS and it's working. The problem is that I also want to connect...
I put my code before ble_stack_init()
reset_reason = NRF_POWER->RESETREAS;
NRF_LOG_PRINTF("reset_reason: 0x%08x.\n",reset_reason );
//NRF_POWER->RESETREAS = 0xffffffff;...
Is it possible to receive connections without setting up a GATT service
For security reasons, I would prefer if generic apps and also the new Web BLE API could make connections...
Hi,
I loaded the code available at github for system on wakeup on gpio current and measured the current in low power mode by connecting a multimeter to a nrf51 dk.
The...
hi,
I am working with nrf51822 board using softdevice(s130).I am making ble initialization and continuously calling the power_manage() function in which sd_app_evt_wait(...
Before post this question. I post the MY QUESTION in stackoverflow forum.
but I couldn't find solution.
I know that Nordic board set Bluetooth Low Energy(BLE) multiple...
