Hi,
Is it not possible to import a key which can be used for multiple use cases?
I would like to import a single key which can be used for HMAC & HKDF.
Is the below...
System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
Hi everyone,
I'm currently working on measuring the power consumption of the 9160DK board and following the guide: Getting started with current measurements on the nRF9160...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi,
a couple of days ago, I had to install some STM plugins for VS Code (I'm sorry ).
In the process, the "CMake Tools" from Microsoft were also installed. I remember...
nRF52840 NCS 3.0.1 MCUBOOT
OTBR on Raspberry Pi 4
I am running the OTBR on a Raspberry Pi 4 with the RCP on a dongle. I am running the coap_client on a nRF52840DK. I have...
I have a bit of a strange problem.
I am designing a signal Gazell signal repeater.
It listens in host mode then sets itself as a device to pass the data along.
However...
Is it possible to put the nRF52 into recieve only mode (say through direct test mode) so that the input impedance can be measured using a VNA? Is the input impedance of the...
When I initialize PPI after timer1 has been initialized I get a fatal error (and reset).
Code:
const nrf_drv_timer_t timer1 = NRF_DRV_TIMER_INSTANCE(1);
nrf_ppi_channel_t...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
Are there any nRF51 demo firmware implementing paring function that the central and peripheral devices will connect automatically without user interaction when they come ...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
I have purchased a red bear lab ble nano board with nrf51822 and a PICTAIL board with microchip RN4020 chip. i have set Tx power 4 for both boards. The rssi value shown in...
This may just be a preference or architecturing question but I thought I'd ask in case there was anything I'm not thinking of, or benefit of one or the other.
I have 2...
Hello,i am find an interesting phenomenon recently.I have a Nordic 5182 device(role as peripheral) and bonded to an iOS device(role as master),when i put the iOS device near...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
