Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi all,
context: nrf52, iot sdk and ipv6; initially rpi as "border router"
question: What can be used as professional/industrial "border router" instead...
Hello,
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here , Intel Curie module integrates nRF51822.
I was wondering...
I'm in the process of trying to start my custom application based on the ble_app_multilink_central_s130_pca10028 example found in the SDK. When I run the app on the nRF51...
Hello everyone,
I am trying to use Segger Embedded Studio for a simple explerimental project.
I started from the sample FDS example from github and build something on...
Hello,
I have an application that uses the Soft-Device. That application want to start a SPI-Bootloader. That SPI-Bootloader isn't the only bootloader on the device, so...
Hi,
I have nrf52 setup as central and peripheral.
As central it connects to another peripheral and everything works just fine. After it did connect I turn of peripheral...
Hi,
I have the NRF52 dongle that is set up as the client and is searching using the ble_app_uart_c (Found in examples\ble_central) example and I am trying to connect a...
SDK11, nRF51422.
Is it safe to use pstorage and fstorage at the same time?
I want to use fds for data storage in my firmware, but device_manager_peripheral.c requires...
Hi, I am trying to read a 24-bit register (with 8-bit address) using the I2C (nrf52). And the timing diagram is given below.
Basically I created a 3-element array (24...
I am having trouble getting the experimental ble_app_multirole_lesc example working with Android and nRF Connect. It is working fine in iOS. I am using v12.1.0 of the SDK...
hi..
i'm trying to use cmsis pack on nordic nrf52 with make command to get to cpu registers and have the folowing error:
Compiling file: main.c
In file included from...
Hi,
I was testing our product with PPK today and noticed one weird problem,- it seems that time is incorrectly displayed in the PPK software. Please have a look on the...
I have customised the ble_app_uart example for my application and the modified code works with the DK board. When I wanted to deploy this to the beacon board (pca20006), I...
I am using the SAADC on a NRF52 to read the battery voltage.
Everthing works fine on the NRF52 DK board but on my custom board I get around
the half of the real voltage...
