Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
just a simple question: I need to create an update over the air system with my nrf52 and I was wondering if transferring the new image to the chip requires especial...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
In sample project I didn't find any way to perform an update through UART like previous SDK.
Nrfutil tool documentation specify that :
Performing a Device Firmware...
Hello, per the question, how?
Is there certain register in the nrf514xx devices which can be called up in debug mode & used for such a purpose? By that I mean:
place...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I'm using the nRF52DK and S132. Is it possible to encrypt a link without any pairing, bonding and authentication process ? Please show me the way how to implement with the...
Hello.
I need to create multiple btle apps with support for the following network topology:
1 btle sensor node; it implements hrs
and bas services
1...
Hi All,
I need to certificate the nrf52 to Fcc. I understood that the radio test is very useful.
I try to clarify what the code permit to do, because i want to adapt it...
I must create an application for nrf5 dk with s132 v3.0.0 sd. In this application a device must implement heart rate service client, while continously trasmitting a reference...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
Hi
I am presently working on MPU92/65 sensor interfacing with TWI/I2C.
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v12.2.0 and keil...
using
nrfjprog --rbp all
and got a success
and using
nrfjprog --readuicr
got unavaible
but if using j-flash and read whole chip, it's able to be readback...
it...
I am trying to figure out how/if I can program the softdevice hex from keil? I know I can just use nRF studio however its annoying sometimes....I also noticed I cannot rebuild...
I'm using an nrf52dk (pca10040) to develop an mqtt subscriber application.
I'm using the IoT softdevice, with the IoT 0.9.0 sdk example for subscriber as a starting point...
