Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hello everyone~
Although one TWIM interface of the nRF52832 can "interconnect up to 127 individually addressable devices", I still think that use different interface will...
Hello everybody.
I'm trying to modify the original firmware that comes with the nRF51822 to make it sweep all of the permitted levels of transmission power.
I was able...
Hello,
I want to read the temperature value continuously on mobile scanner app. I implemented the program as stated in BLE Characteristics beginner tutorial and I am using...
Hey guys,
I’m trying to come up with a way to know if an advertisement was received via BLE_GAP_EVT_SCAN_REQ_REPORT, but then not actually send the SCAN response. It’s...
Iam using softdivice 110 and sdk 10.0.0, iam using spi driver for interfacing with spi slave device(flash memory device). I need to send command and then receive the data...
Hi,
I am trying to implement an ECG measurement device. nRF52832 collects the sensor value through SPI and send it to smartphone using ble_app_uart code. I need to send...
as sd132v3.0.0 got some Exciting functions.
I tried to use in my production.
everything work fine, except for dfu.
Trouble is:
when i upgrade from softdevice 2.0.1...
Hi, I am working on reading battery voltage of nRF51822 Microcontroller.
I have used the openbecon(internet) code for ADC configuration and reading.
I am getting 28...
Hello,
I am trying to update temperature value through BLE characteristics example but while temperature update in following function I am getting error code 12291.
...
Hi i have to read some data from a temperature sensor.
twi_temp_read((int8_t *)&temperature);
this below what do?
temperature = ((temperature >> 12) & 0x000F) ...
Hi,
In SDK12_NRF52 custom project not work to me NRF_LOG_MODULE, I have this in main.c top:
#include <stdint.h>
#include <string.h>
#include "nordic_common.h"
#include...
MyZip (1).zip Hello,
I'm trying to run a ADC example for nRF51822 in Keil 5.21 MDK, but error is raised up.
I've done following before:
-installing all packs,
-tick...
