Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi Nordic Team,
Please I would like to ask how can I globally identify my device (nRF51822) based on its address?
Assuming that:
The address type of nRF51 is...
Hi all,
Is it possible to place your own antenna into nrf51822 bluetooth smart beacon kit? if it's possible, how am i going to do it?
am i suppose to remove the antenna...
I made a custom BLE device using nrf51822 and need to do DFU from remote place.
The BLE device is connected using USB to windows PC.
The Serial bootloader examples are...
I am using the nRF52840 Preview DK with BLE 5.0. In the BLE ATT_MTU Throughput Example,I use several api such as sd_ble_gatts_value_get and so on,but i still can not read...
Hello,
I'm using several gpiote interrupts in SDK 12.0.1.
I want to know the max number of low power input pins.
My configuration in sdk_config.h is like below.
thanks...
Hi,
I need to read more than 3 or 4 Bluetooth Heart Rate Sensors (like chest strap, arm band, and so on)... I need to do this using Arduino and some library.
Could someone...
I'm using the ble_app_hrs_adc_battery_measurement example ADC code in my project
However, I don't understand what these lines do
github.com/.../main.c
As far as I...
I am trying to add spi communication to the twi_master_with_twis_slave project because I need to communicate with two different sensors. I have included nrf_drv_spi.h and...
Hi,
in the NRF52832 documentation the TX chain delay is 0.6 µs while the RX chain delay is 9.4µs.
Does that mean if transmitting two packets in a row to the same receiver...
Hello everyone,
I have been using nrf52 IoT SDK for MQTT implementation. Everything works fine as long as I am publishing or receiving only one character i.e.
param...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
In Eddystone example in SDK 12.2.0, APP_MAX_ADV_SLOTS parameter is by default 5, but if I try to use less than 5, an error appears in es_flash.c because in the code, 5 slots...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
