Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi Nordic
I am using ESB_DPL protocol between two 51822 to do RF communication.
First i put two device very close, works very good, no packet loss, then I moved the...
After spending substantial time without luck I will drop my question here.
Setup
nRF5_SDK_12.1.0_0d23e2a -> bootloader_secure debug target
nRF51 & nRF52
IAR...
Hi,
I am using simple ADC peripheral to read internal battery voltage(standalone). I am using two custom nRF51822 boards. One of the nRF51822 board is made by nRF51822...
Hello. I just started learn ble module and some confusing about ble_app_uart:
in file ble_nus.c we have function on_write this function calling when trigerred BLE_GATTS_EVT_WRITE...
I am developing a android app for firmware update on my device. I used buttonless dfu example to switch from application mode to bootloader mode, I write value 0x01 to the...
I'm trying to track down who is erasing and programming 0x800..0xFFF.
Does the SD_MBR_COMMAND_COPY_BL modify 0x800..0xFFF?
I inserted a CRC32 at the end of the MBR ...
How should we comprehend the nature of PPI, when dealing with radio interrupts?
For example, if I point radio event handler call back ( of this type:
static nrf_radio_signal_callback_return_param_t...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
