Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
I am debugging in an environment using BLE with nRF54, but after breaking, when I step through it, the debugger stops and I am having trouble.
The environment...
Hi All,
For our project we need to keep data about devices in sort of a backend service so they can be shared by several mobile phones, including some iOS devices.
iOS...
I've been testing the littlefs sample on NCS v2.8.0 and v2.9.0 with an external SD card. Initially I tested the sample with an nRF52840-DK and everything worked as expected...
I'm getting the following notice/warning/error when building my application (nrfsdk 2.9.0 w/ sysbuild, nrf9151dk board):
/usr/local/zephyr-sdk-0.17.0/arm-zephyr-eabi/bin...
Using nrfutil/dfu, I have previously flashed an older application+SD (s132_nrf52_3.0.0) onto the nRF52840 dongle.
Now, I cannot flash my newer application, since it contains...
Hi All,
Simply put I am trying to use the Xiao BLE Sense board connected to the Expansion board (with SD card slot) to write audio recorded data from the Xiao embedded PDM...
Hello, I'm programing my project while using the nrf52840 chip. I'm using segger embedded studio for the programming part because with the nrfconnect I have error code 9 ...
Hi I wish to integrate Matter over thread in unicast audio server . My objective is to use matter to control the volume and play/mute states. I would like to know whether...
Hello, checking if it's at all possible to have uart working on the nrf52832-dk using pins 18 and 21. I can get rx/tx working with an ftdi using pin 12 & 13, but not 18 &...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
