Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
I’m using nrfjprog version 10.12.1 and JLinkARM.dll version 6.88 . I encountered an intermittent nrfjprog error when programming firmware to the nRF52833 .
In most cases...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hello Team,
I’m working on creating a custom Matter cluster using the instructions provided in the Nordic documentation: https://docs.nordicsemi.com/bundle/ncs-latest/page...
I'm getting the following warning on my terminal during build:
-- Including generated dts.cmake file: D:/Workspaces/azure_iot_hub_9/build_pmi/mcuboot/zephyr/dts.cmake CMake...
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
Hello DevZone,
I have learned that some knowledge about CLOCK. But they are a little bit confusing. I just want to get confirmed by any expert.
1. Some peripherals ...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
I am working with the WLCSP version part (nRF54L15-CAAA) and it calls out that there is light sensitivity. The note seems to indicate that only underfill around the perimeter...
how to upload modem firmware and and connect to nrf cloud and send modem firmware and asset tracker hex file and procedure to connect to nrf cloud ( i tried and sim activated...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I get the source code from the github.com/.../ncs-fund.git , and trying to build the exercise-1-5 of nrf-connect-sdk-fundamenta lesson-4-serial-communication-uart for 54l15dk...
