I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Dear Nordic Team,
I hope this message finds you well.
We are currently working on a project that requires generating continuous traffic using Classic Bluetooth, and if...
Hi.
Could you please tell me how to change the order of services in nRF Connect Mobile?
I want the list to show Bluetooth Service first and then Battery Service.
Can...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Dear Dev Team,
I am currently working on implementing OTA DFU on the nRF52832-DK using the Arduino framework. However, I have not been able to find any suitable options...
Hello!
I am currently using INA219 (Zephyr I2C driver included) current monitor to test I2C function on nrf54l15dk, but the board cannot recognise the sensor successfully...
I am trying to build using a custom board and 2.9.1, but am getting these errors:
My dts looks like this:
I have the width specified. Much of this is over...
I am currently looking into the Legacy DFU process. Currently the only way to actually conduct a Legacy DFU is via the nRF Connect Mobile App. After conducting a successful...
Currently using NCS v2.9.1 nrf54l15/cpuapp custom board derived from nrf54l15dk, customization to de added after solving the issue below.
The project is successfully compiled...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
We have developed a hardware platform using the NRF5340 on Nordic's zephyr (version 3.5).
Our current consumption in idle mode is still around 330 µA, instead of the expected...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Hi, I'm working on the DK for nrf52832. I have a working code for BLE, and another working code for die temperature using interrupt. Now I want to merge them and trigger the...
