Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The documentation for the nRF52840's SAADC mention optional resistor ladders. What are they for? I see that the documentation specifies that the ladder's resistance is 160kΩ...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
I guess the answer is yes, because I know Characteristic Declaration (UUID 0x2803) has an unique handle for each characteristic.
Just wanted to confirm.
Its the first time I use simple_timer. I do not use the Softdevice. So I'm working with the peripeheral simple_timer example(SDK11).
I know from the app_timer, that every...
Hei!
I recently added WDT to my existing project. After that the normal behavior/sequence of code is not as it is supposed to. Strangely it works okay every other run now...
I just get DK P10040, I am using SDK_11.0.0_89a8197/s132_nrf52_2.0.1_softdevice.
I tried ble_app_uart, it works.
But I find a problem, I cannot set P0.09/10/12/13 high or...
I'm trying to compile nRF51 SDK 8.0.0 under Windows.
So for that purpose I'm going to components/toolchain/gcc and running 'make' there.
No targets specified and no makefile...
Hello,
I find in your source code contradictory values for the UART TX and RX characteristics.
E.g. have a look at nRF toolbox (both Android and IOS) definitions: github...
Hi all,
I am trying to implement DFU on my device with marginal success. Here are the steps that cause the issue:
Using nRFgo Studio: "Erase all", "Program Softdevice...
hi
I use S130 from nRF5_SDK_11.0.0_89a8197 as an ble central base on ble_app_uart_c example. when the ble_peripheral change the adv's content(means have data to send),the...
I have been able to follow the instructions in the nrf5 iot sdk to connect my nrf52 dk to a raspberry pi, however I am unsure why a connection must first be made before I...
Hi,
I'm using nrf52 with S132. I noticed high current draw after calling sd_ecb_block_encrypt() function.
After calling function consumption is 6mA and stays at a constant...
Hi,
I would like to read and update value of the characteristic received from AD pin AIN0. I already tested the following code, where I got very weird results (value is...
I am using Keil MDK v5.2 to compile ble_app_uart example using the project in examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I am using the latest nRF5_SDK_11...
I would like to use the capsense example with a Bluetooth application. But as it's not compatible with softdevice, I want to modify it. Two questions:
1 – As anyone already...
HI,
I have very basic question: I plan to connect two devices on i2c to the nrf52. Can they both be connected to the same pins, and configured by software to select one...
