Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi All,
I have enabled the UART service in my beacon application.I Configured write access and write permission to characteristic UUID. I got connected to the device and...
Hi!
I am new to the embedded world and am trying to interface a NRF52 DK with a MPU 6050 accelerator/gyroscope. Right now, I have been able to interface the MPU 6050 with...
file.txt Hi,
In my application I am using UART service which receives the data sent from APP. I am using nrf connect APP. I am sending simply 1 and 2 from UART service...
Hi.
I develop an application in the past with ARDUINO and a nRF24AP2 module with great success. I can read 8 heart rate monitors ANT+ sensors in the same time, with 8 differents...
I am a newbie in embedded programming. I want to encrypt some advertising data using aes-ecb API, provided by the softdevice but I am not getting any encrypted data after...
Hi,
We are currently using SDK 10 experimental boot loader example. We would like to encrypt the firmware before creating the zip file for OTA. The procedure we followed...
Hello everyone,
I am trying to use BLE module on nRF51 in central (oberserver) mode using IOT Softdevice. I want to scan for any device around my board.
I get error when...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello All,
I am interfacing WS2812 RGB ringx16 with nRF51822 and use nrf51-neopixel library from github.com/.../nrf51-neopixel
Its not working.
for example : value...
Hello,
I was looking into Gazell and read that Gazell only allows pairing when Host and Device are in close proximity to each other. This range is about 30 centimeters...
I'm trying to maximize BLE throughput between a central and peripheral (I'm programming both) running the new s132 SoftDevice v3.0. I can't achieve the maximum data payload...
I am trying to use the NRF51 dongle (PCA10000, firmware ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex) with the sniffer software but on selecting a sniff source and starting...
Hey,
I successfully build and load the ble_uart_pca10028_s130. Now i want to edit something to the Code and this error is shown up.
I think I have to include something...
Hi there, I have done search and know there are several similar questions, but unfortunately I didn't find any useful answer after carefully reading through them, thus I decide...
Hello,
I've just read the thread explaining the UART baudrate register settings. I then looked at the nrf52_bitfields.h file and found that the baudrate register values...
