I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here , Intel Curie module integrates nRF51822.
I was wondering...
I'm in the process of trying to start my custom application based on the ble_app_multilink_central_s130_pca10028 example found in the SDK. When I run the app on the nRF51...
Hello everyone,
I am trying to use Segger Embedded Studio for a simple explerimental project.
I started from the sample FDS example from github and build something on...
Hello,
I have an application that uses the Soft-Device. That application want to start a SPI-Bootloader. That SPI-Bootloader isn't the only bootloader on the device, so...
Hi,
I have nrf52 setup as central and peripheral.
As central it connects to another peripheral and everything works just fine. After it did connect I turn of peripheral...
Hi,
I have the NRF52 dongle that is set up as the client and is searching using the ble_app_uart_c (Found in examples\ble_central) example and I am trying to connect a...
SDK11, nRF51422.
Is it safe to use pstorage and fstorage at the same time?
I want to use fds for data storage in my firmware, but device_manager_peripheral.c requires...
Hi, I am trying to read a 24-bit register (with 8-bit address) using the I2C (nrf52). And the timing diagram is given below.
Basically I created a 3-element array (24...
I am having trouble getting the experimental ble_app_multirole_lesc example working with Android and nRF Connect. It is working fine in iOS. I am using v12.1.0 of the SDK...
hi..
i'm trying to use cmsis pack on nordic nrf52 with make command to get to cpu registers and have the folowing error:
Compiling file: main.c
In file included from...
Hi,
I was testing our product with PPK today and noticed one weird problem,- it seems that time is incorrectly displayed in the PPK software. Please have a look on the...
I have customised the ble_app_uart example for my application and the modified code works with the DK board. When I wanted to deploy this to the beacon board (pca20006), I...
I am using the SAADC on a NRF52 to read the battery voltage.
Everthing works fine on the NRF52 DK board but on my custom board I get around
the half of the real voltage...
Hi Nordic Semiconductor's community,
I have a question about the function sd_ble_gatts_value_set(), more precisely about if it is
possible to set the CCCD value of a characteristic...
