Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
Hi,
do you have any tutorial for contiki on windows based.
no matter which platform you are using.
i am using the ecilpse with cygwin toolchain in ecilpse.
i follow...
Hi,
I'm trying to compare current consumed for different sets of commands mainly with floating point operations in them. As they execute fast, I'm putting them in a loop...
Are there any plans to add write capabilities to the NFC driver? The hardware supports it, but the library provided by Nordic does not (as far as I know). Are there any plans...
I started evaluating the nRF52 using Keil and everything worked great. However, I switched to developing in IAR because I have a full license. I'm using the same code (ble...
Hello Nordic,
I just read the news from may about the arduino primo and i am really exicted!!
I have been tring to decide between arduino due, or some complex ensemble...
I'm developing an application on a custom nRF52 board. I have no problem to program the board with Keil. However when I try to program the application with the nrfjprog, the...
Hi all,
I have been porting a project from SDK 8 to SDK12, andi have ported one of the services, however when i add a characteristic it throws
:ERROR:From File error...
Hello,
in my current project we develop a BLE firmware which runs on a custom board based on a Telit +s42 module (with integrated nRF52 SoC).
We are able to flash the...
Hi,
I am a bit confused from the example, in the specs it is said that writing the flash is word allign, and even so the example does something strange:
do
...
hi.
this is my code that i copied from ble_app_hrs_rtx .
osPoolDef(ble_evt_pool, 8, ble_evt_t); /**< Definition of memory pool for ble_stack_thread */
osPoolId ble_evt_pool;...
The ShockBurst bitrate mode ( nrf_esb_bitrate_t ) NRF_ESB_BITRATE_1MBPS_BLE is described as '1 Mb radio mode using Bluetooth low energy radio parameters.' in the SDK documentation...
