Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I'm having an issue getting strings to print properly using the RTT and the logging module. Literal strings seem to work fine. I.E. the following works perfectly:
NRF_LOG_INFO...
Hello,
I am working on an nRF52 project that uses the SoftDevice S132 v3.0.0. The system supports BLE observer, BLE central, and ESB functions. BLE central and observer work...
Hello everybody,
I have a NRF51-DK board and I want to acquire some NRF24LE1 chips. I haven't used the NRF51-DK a lot but I have seen somewhere that it is possible to flash...
Hello Nordic,
I have a question: how do I send a message from a slave to a master? I want to do the same as sd_ant_acknowledge_message_tx, starting the communication from...
Hi,
I am using nRF51422 DK with S130 SoftDevice. I modified ble_app_uart example and I saw my board show in bluetooth setting of my android phone but dit not see anything...
Dear Nordic,
We have a very strange issue regarding NRF52 consumption.
We found that the NRF52 will continously consume 7mA even when we enter in sd_app_evt_wait().
After...
Sorry about a so broad question. But this is what I have experienced but don't know where to look.
I have done a few project using BLE with RTX. Just typical stuff similar...
For Setting the easyDMA on I2C, Do I need just to set the TWI0_USE_EASY_DMA to 1 ?
Also do I need to set an arrayList? which?
or can I just use the same settings that...
Hello,
My team wants to develop a custom iphone application and we want to use it to connect with NRF52 which is transmitting data using the Nordic UART service. We were...
Hii,
I am trying to update new firmware in nRF51-DK.
But unfortunately, wrong image file is uploaded.
Now i am trying to once again same process then getting no space...
I am testing the SDK (v12) Power Profile Example with the DK51 and the nRF51 dongle. My purpose is test if I can lower the power consumption as mush as possible. The default...
I am developing software for a custom hardware based on NRF52. Previously I was tasked on updating the old NRF51 based software (used on older version of the device) for NRF52...
hi,
i am using FDS to store some Data in nRF51 Development kit using temporary application. it is around 2kb. after that i am flashing main Application. is my application...
I am working on a battery-powered application. Since power saving is a must, this design using high-side power node controllers (part number MIC94042) to power-on or power...
