Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello, Nordic Team! I am encountering a such problem when using the NRF54L15 on NCS3.0.2 to develop a Matter product. I am trying to use the
SubscribeAttribute
method...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Hi,
I got the PWM example code working, but I need only 3 PWM pulses (14usec on time and 34 usec off time). How do I configure the PWM pins to output just 'n' cycles? thanks...
Hello,
I have downloaded the nrf52 sdk (version 0.9.2) and following the steps listed here: infocenter.nordicsemi.com/index.jsp , to run the blinky led example. However,...
hi, i'm looking for layout and schematic (altium ver.) of attatched nrf module (nrf 51822 BLE).
how ans where can i get this ????
actually i need the imformation...
Hi,
For each sdk version there is a release note of known bugs which is good :-)
I guess it lists the bugs known at the time of the release of the sdk.
Are these posts...
Hello,
I am developing in NRF51 with gazelle communication. I specify in project setting (in IRAM) to use full RAM of my nRF51, and use MicroLib. My last working application...
Hi,
I wonder if anyone knows any free C++ compilers for nRF52. I tried the mbed but it is not fully supported for nRF52.
The regular GNU GCC: arm-none-eabi-gcc works perfectly...
We are working on a project using the nrf52832 (SoftDevice s332 v0.9.1alpha, nRF5 SDK 11.0.0) in which we build a library as a hex file and and load it into a known flash...
Hi Guys,
I am using Bluez 5.39 on Ubuntu 14-04 acts a the peripheral by running "example-gatt-server" which creates 3 services and serveral characteristics within it. ...
In a project, I know the Bluetooth address from the machine, also know the phone's address. I want to let Bluetooth devices from the computer and mobile phone side of Bluetooth...
When I use the example of ble_app_uart(SDK : nRF5_SDK_11.0.0_89a8197) to measure data througput ,I find that i cannot get the complete packet of 20 bytes.
The operation is...
ble_ant_app_hrm.rar Hi!!
I want to design dual mode(BLE UART +ANT) but unfortunately I can not built it well.
Can anyone tell me what kind of function or parameter? I based...
Hello,
I am using the nRF51 dongle to try to observe the packets sent between two soft devices. I have inserted the dongle into one of my PC's USB drives and am holding...
I'm running s120 v1.2 & SDK 9
My application will connect to, up to 8, known peripherals. If the connection is dropped or not established, my central app will try to continue...
By trial and error, I notice that I can only write 20 bytes to a characteristic, no matter how big I make ble_gatts_attr_t.max_len. A little googling reveals that this is...
