Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Is it possible through the API/Softdevice to do one of the following:
read out the current advertising data structure, change a the manufacturing data field, and...
Hi,
I am planning to use modules with nRF8002 in an indoor positioning application.
The mobile devices that are to be located are continuously scanning for BLE devices and...
Hi, got an interesting problem, this is on a custom board with nRF51822 QFAB that we are bringing up. The radio test (not using softdevice) works ok and produces strong transmit...
Hi
Could you provide the power current in System on Active, System on Sleep, and System OFF for nRFready Desktop2 keyboard and mouse? nRF51 was programmed Desktop 2 v1.0...
Hello,
I am working on the factory test mode and I want to add a carrier test, is there a function from the S110 softdevice library that I could use?
Thank you for your...
Hi,
I set up eclipse according to n-AN29 and imported several of the example projects. The blinky_example project described in the nRF51822 dev kit user's guide works perfectly...
Hi, I have been trying to maximize the baud rate of my uart module, I am using the app_uart layer to control the uart and I have noticed that in your implementation of HCI...
I have an ultra low power application that needs to broadcast it's proximity on a 1sec interval. However, about 75% of the day I would like the device to be powered down and...
Hi all
Now I can use Keil to compile/load/execute the example project, for example blink.uvproj.
But how to execute/debug on ble_app_hrs example ?
Keil will hang on a...
I am looking for details on the internal temperature sensor on the nRF51822. I would like to use it to get a general ambient reading of the air around the device. Basically...
I want to get RSSI between PCA10001 and PCA10000. As you known, I have to make these two device connected first. If I write my code based on the example of UART, are these...
Hi,
i need to start my application while pressing two seconds a button. For this i use an gpiote event like here --> devzone.nordicsemi.com/.../how-to-use-app_timer_cnt_diff_compute...
hi everyone.now i am developing a project with nrf51822.i am using the PCA10000 dongle to see some information of advertising packages. i moved out and pluged in the PCA10001...
